Extreme repair W212 rear air conditioning deflector_vehicles, vehicles

Extreme repair W212 rear air conditioning deflector

September 4, 2024

Send a repair W212 rear air conditioning port pick repair tutorial, the recent pick aging fracture, including the inner guide plate base disconnection caused by falling problems.
The fracture of the outer guide plate pick can be repaired, but it is not ideal. I directly put 2 silver on the XX. As for why the silver is too lazy to toss about, the apricot color found to be sticky several times is estimated to be caused by the high temperature.
Inner guide plate pick, air conditioning cover are available to buy, but small problems can be repaired, after all, it is still the original factory parts.
(the professional name can not be said, the outer guide plate I mean that the outermost blade can be moved up and down, and the inner guide plate is the blade plucked left and right inside)

The main purpose of this tutorial is to repair the inner deflector base, and it is also applicable to replace the pluck base foot.

The tutorial is suitable for the operation of replacing the black foot of the pick. This pick is not necessary to repair, compared with me to repair with a high-temperature welding torch, poking is not smooth, so online Amoy 2 is not expensive, about 12 yuan.

1. Maybe many people don’t know how to open the rear air-conditioning panel. I also checked the information and video for a long time before I saw that when I opened the saddle box, there were two grooves in the mouth of the rear air-conditioning panel, and the panel could be pulled out with a small screwdriver.

Look at the picture on the top two notches, poked in from the saddle box with a word screwdriver.

two。 After removing the rear air conditioning panel, there are sticking feet on all four sides of the air black trough, which is really difficult to take out, because you need to open the slot foot at the same time to take it off. I use toothpicks here. All eight stickers are stuck with toothpicks, and the remaining two bottommost ones can only be pried with a word screwdriver.
If you look at the wire harness as the bottom, there are 1 foot on the black slot, 2 feet on the left and right sides, 1 foot on the inside and 1 foot on the bottom. There are a total of 10 stickers.

3. As shown in the picture below, the base of the inner deflector is broken, and I can’t find where I dropped it. The pick fell out and the position could not be limited. What I use here is a small pin for positioning, remove the other needle, bend it with sharp-nosed pliers and make the base of the deflector. Finally, use a high-temperature welding torch to trap the pin into the plastic cover.

Note: after the black slot is removed here, the front guide plate blade has a headache here, and the blade has no black groove foot limit, so it is easy to fall out, and you have to adjust the blade before you install it. You need to be patient, otherwise you are not recommended to toss around. It took me dozens of minutes to adjust this front deflector blade.

The base of the deflector was broken after aging, so it fell out without a limit. The five feet protruding from the edge of the black groove are the blades of the front baffle.

Pin to the head, keep the bottom, bend to fit the black slot.

This is the situation after repair, pin limit. After being fixed, the test is normal.

When installed back, the front baffle blade is more messy. If the holes are not aligned, it is difficult to get stuck after installation, so this one needs to be more careful. There is an ash layer on the page for a long time. Rinse directly with clean water and dry the water with a hair dryer.

4. Install it back. There is a vertical line on both sides of the black groove, aim at the saddle box base line slot, press down from the top down, and finally press the tight base. At first, I had been aiming at the two corners of the base, but the front and back propulsion couldn’t get stuck, so I found that I had to insert the lines up and down. If you don’t understand the text, you can see figure 1. There are two slot corners above the air conditioner port.