Time; September 2019
Location; home of the president of the car club.
Character; 16 Boyue
Objective: to replace the injured rear anti-collision beam before the National Day.
On the eve of National Day, the president upgraded the rear collision beam just to replace my last damaged anti-collision beam. Although it is not serious, it is necessary to follow in order to travel safely on National Day. Just imagine that the first collision of the anti-collision beam protected the safety of the people on board, cracked a little bit, and encountered the same or greater impact next time. Then its protection will be greatly reduced, and many accidents can actually be reduced.
When I went out for a trip to a different place, I didn’t know what happened in front of the highway. My front car slammed on the brakes and I didn’t hit the brakes with the help of the powerful Boyue pre-collision function. But the car behind me didn’t stop and hit my white ass hard. Only then did I know how important the safe car-following distance is, especially on the highway. After getting out of the car to take pictures, seeing that the appearance collision was not serious, he charged the other party a piece of back board and maintenance fee, after all, it was not intentional. At that time, I felt strange that the speed should be about 4-50 per hour when I was hit. How can I get a little hanging injury? Later, when I went home and opened it, I found that there was a crack in the anti-collision beam inside. The experience here tells you that when it is safe to get hit on the highway, climb down to the bottom of the car and have a look at the anti-collision beam, which is more expensive than the outer panel.
Boyue in the rear collision beam is not steel, not aluminum alloy, but fiberglass material. Under the same quality, the overall strength of FRP is better than that of steel, and at the same strength, the weight of FRP is lighter than that of steel. The rear collision beam of Boyue should protrude from the rear box door. In the event of a collision at the rear of the car, the rear collision beam will protect the rear box door from damage.
Prelude
I didn’t know the rear-end of the N-car until I got off the bus.
I was rear-ended, too.
The brakes of the pre-impact function are clear.
If only you had the function of pre-collision.
The appearance is just a scratch on the shell.
Close-up
The picture shows that the replacement of the anti-collision beam after Boyue begins.
Remove the taillight first.
After taking out the screw, beat back and forth to remove the lamp assembly, you have to use skillful force.
Pull out the wire harness
Pull out the card.
There are also three screws and sticking at the bottom of the car. Take them out from the left position.
Take out the middle position
Take out the position on the right
Now the order is at the position of the rear wheel eyebrow.
Take out the rear part of the eyebrow
The screws here are connected to the rear beam cover and should be removed.
The screws connected at the eyebrows of the rear wheels on both sides are removed before the back cover is moved. the key to taking the back cover is still those two words-Qiao Li.
Note that when the rear cover is removed, someone has to lift and pull out the radar harness before it can be completely detached.
Unplug the wire harness connecting the rear cover
Pay attention to the placement after detaching. The position of the contact point between the back cover and the ground must be covered by something with a soft shell.
The Boyue FRP anti-collision beam appears, and the downlink card is taken out at this time.
Detached radar harness
Use a 13-size barrel to remove the screw connecting the anti-collision beam.
Take off the anti-collision beam and watch the cracks on the fingers.
Outside close-up
Inside close-up
Boyue is on the right side of the energy absorption box, and the traction bolt is here.
Left energy absorption box
Replace it with the original anti-collision beam [or the first 16 cars]
Homing radar harness
Note that the last back cover must be aligned with both exhaust vents before it can be easily deducted-it is much easier for Qiaoli to find the right point.
Taillight return to position
After the completion of the big white sexy buttocks finish.
It takes about 20 minutes for Boyue to replace the collision beam. Once again, I would like to thank the president of Guizhou Boyue car Association for his personal help. At the same time, I hope the next assignment can help you.