Replace the fog lights for my LaVida
MyrnaHudson 
9 To protect safety-replace the fog light bulb. The car was bought as a trump card and did not have front fog lights. However, personally, it was not good to have no front fog lights. At first, he didn’t install them because he didn’t understand them. Later, after understanding from various aspects, he decided to install front fog lights, and then he bought various accessories, and then added the front fog lights himself. Just at the end of January 2019, I drove on the front fog lamp at night when I was approaching the Chinese New Year, and found that it didn’t feel like it was on in the driver’s seat. I looked down and found that it was no longer there. It had only been installed for less than a year. What is this? The situation? Then I checked it down and found that the fog light bulb was burned. Since there was no place to buy the light bulb at night, I hadn’t changed it and installed it for a long time, and I forgot it again.
When I happened to think of this, I went to the car repair shop below to ask. In the end, I bought a light bulb that had been removed in his shop but didn’t buy a new one. Then, after work, I installed it at home for nothing. Without saying much, I started work. It’s very simple.
Preparations:
1. Precautions before installation: Look at your safe side and shoot it to the other side. Since I was changing the fog lamp for driving, I drove the car to the right and killed it, and then turned off the engine. It is best to prepare gloves because they are dirty here. And cut off the power before replacing it. After fog lights are installed, the sockets must face downward to prevent the risk of water short circuits.
2. Tool: One rice wrench
3. Accessories: One fog lamp H8- 35W bulb
Installation:
1. After turning the direction to the right, use a rice wrench to remove the three screws fixing the fender lining and bumper. You can also remove the next two. Personally, I feel that the space for removing the two is a little small and it is difficult to reach out inside.
Installation:
When I happened to think of this, I went to the car repair shop below to ask. In the end, I bought a light bulb that had been removed in his shop but didn’t buy a new one. Then, after work, I installed it at home for nothing. Without saying much, I started work. It’s very simple.
Preparations:
1. Precautions before installation: Look at your safe side and shoot it to the other side. Since I was changing the fog lamp for driving, I drove the car to the right and killed it, and then turned off the engine. It is best to prepare gloves because they are dirty here. And cut off the power before replacing it. After fog lights are installed, the sockets must face downward to prevent the risk of water short circuits.
2. Tool: One rice wrench
3. Accessories: One fog lamp H8- 35W bulb
Installation:
1. After turning the direction to the right, use a rice wrench to remove the three screws fixing the fender lining and bumper. You can also remove the next two. Personally, I feel that the space for removing the two is a little small and it is difficult to reach out inside.
Installation:
1. After turning the direction to the right, use a rice wrench to remove the three screws fixing the fender lining and bumper. You can also remove the lower two screws. Personally, I feel that the space for removing the two is a little small and I can’t reach out inside.
2. Then reach out with your hand from this place, find the position of the fog lamp, and rotate the fog lamp counterclockwise with your hand. You can watch from the front. When Wood turns it to the floating position, he pulls the fog lamp out of this place.
3. After pulling it out, just break the clips on both sides to both sides and pull out the fog lamp, so that the fog bulb has already come down. It says H8- 35W
4. Take out the newly purchased second-hand fog bulb and plug it in the original method. It must be fastened tightly and the sealing ring must be inserted in.
5. Return the fog lamp to its original place, or look from the front, insert the fog lamp into the fog lamp shade with your hand, rotate it clockwise and look from the front, and just stick it in place.
6. Put the three screws back into their original positions and fix them tightly with a wrench.
The installation is perfect, and the fog lights are on again, not blind in one eye. The brightness is still okay. When you turn on the lights at night, all four lights will be on.
Hot Information
Tesla Autopilot and similar automated driving systems get ‘poor’ rating from prominent safety group
April 1, 2024 Localization of EV parts without production scalability may not help cut EV price, says President, Amara Raja
March 27, 2024 
JCTSL may turn bus stands into charging points for e-buses
March 27, 2024 You May Like
